DYEDBRO EVO MTB / E-BIKE FRAME PROTECTION - CLEAR MATTE

Iconic patterns are our heritage; EVO is our future. Engineered as the high-tech protection specialist for modern MTB, E-Bike, and Gravel frames, it offers a refined, invisible fit that moves with your ride. Same legendary DYEDBRO toughness, now in a sleek, second-skin finish that’s built to take the hits.

Why install frame protection? Because bikes don’t have an easy time of it. When rocks and debris aren’t being flung at them from the trails, they have to contend with dings, scuffs and scrapes from crashes, parking mishaps and getting too friendly with other bikes on the back of a car or shuttle. DYEDBRO frame protection kits cover all the most vulnerable parts of your frame with a tough, durable barrier to keep what’s underneath looking its best, and they can be easily applied at home.
 

WHAT'S INCLUDED
The EVO MTB/E-Bike kit is designed with extra coverage for the larger down tubes and complex rear triangles of modern trail, enduro, and electric bikes. It provides a heavy-duty shield against rock strikes and high-speed debris.

• 1 x Top Tube Protector

• 2 x Extra pieces for larger frames

• 1 x Down Tube Protector (clear) in heavy-duty 300µm/0.3mm PVC

• 2 x Chainstays Protector

• 2 x Seatstays Protector

•  

  Weight (after installation): 31g 

THE WET-INSTALL ADVANTAGE
Unlike our traditional kits that require heat, EVO is engineered for a soap-and-water application. It’s faster, more precise, and easier to get a factory finish at home. 

MAXIMUM FLEXIBILITY
A high-elasticity film that conforms more easily than conventional protectors to the most hard-to-reach areas of the frame, as well as the beefy tubes of E-Bikes and the sleek lines of Gravel bikes.

SELF-HEALING DNA
EVO is like a “smart skin” for your frame. Small scratches or surface marks disappear when exposed to ambient heat or warm water, as the film’s molecules return to their original state, eliminating these minor imperfections. This self-healing capability helps the surface maintain its appearance and finish for a much longer time.

DYEDBRO EVO INSTALLATION

• Before installation, first thoroughly clean the bicycle frame using a mixture of 50% alcohol and 50% water (some paint finishes can be damaged by 100% alcohol)
• Mix the soap sachet included in the box with between 750 ml and 1 liter of water. Spray the solution onto the area of the frame where the piece will be installed, as well as onto the vinyl itself.
• Wet your fingers when handling the protector to avoid leaving fingerprints on the material.
• Place the piece in position. Initially, use only your fingers to adjust the vinyl. Once correctly positioned, continue pressing the vinyl into place with your fingers. Afterwards, you can gently use the scraper to remove the water trapped underneath.
• Finally, and only at the very end, you can apply a small amount of heat using a hair dryer or heat gun to help evaporate any remaining water. Important: do not apply excessive heat.
• After 24 hours, it is recommended to check the entire installation again. This material gradually evaporates the remaining water, and the final result improves especially after 48 hours.
• We recommend not riding the bicycle until at least 24 hours after installation.

PLEASE NOTE
Certain paint finishes, notably fluoro tones, can be prone to fading over time and areas covered by the frame protection may age differently to exposed paintwork.

DYEDBRO EVO MTB / E-BIKE FRAME PROTECTION - CLEAR MATTE

EVO INSTALLATION

• Before installation, first thoroughly clean the bicycle frame using a mixture of 50% alcohol and 50% water (some paint finishes can be damaged by 100% alcohol)
• Mix the soap sachet included in the box with between 750 ml and 1 liter of water. Spray the solution onto the area of the frame where the piece will be installed, as well as onto the vinyl itself.
• Wet your fingers when handling the protector to avoid leaving fingerprints on the material.
• Place the piece in position. Initially, use only your fingers to adjust the vinyl. Once correctly positioned, continue pressing the vinyl into place with your fingers. Afterwards, you can gently use the scraper to remove the water trapped underneath.
• Finally, and only at the very end, you can apply a small amount of heat using a hair dryer or heat gun to help evaporate any remaining water. Important: do not apply excessive heat.
• After 24 hours, it is recommended to check the entire installation again. This material gradually evaporates the remaining water, and the final result improves especially after 48 hours.
• We recommend not riding the bicycle until at least 24 hours after installation.